2 max sway (any direction) do not scale from this print adhesive)(see fig 6, sht 2) (use k-500-300) -02: surface mount clm-1xx-xx-xx-d-xx no of positions / row -02 thru -50 body spec -d: double row (use clm-xx-d) lead style spec plating specification -f: 3" flash selective gold in contact area matte tin on tail (pre-plated contact) -l: 10" light selective gold in contact area matte tin on tail (pre-plated contact) -g: 10" gold in contact area 3" on tail (post-plated contact) -h: 30" heavy gold in contact area 3" on tail (post-plated contact) -lm: 10" light selective gold in contact area matte tin on tail (pre-plated contact) -fm: 3" flash selective gold in contact area matte tin on tail (pre-plated contact) option -p: pick & place pad (available on pos 7 thru 50 only) (see fig 3, sht 2)(use lmp-04) -tr: tape & reel -be: bottom entry only (see fig 2)(use clm-xx-dbe-xx) -pa: pick & place pad w/ alignment pins (see fig 4, sht 2) -a: alignment pin (use clm-xx-d-xx) (available on pos 3 thru 50 only) (see fig 5, sht 2) -k: polyimide film pad (available on pos 7 thru 50 only) (.005 [.13] thickness with silicone (use c-117-01-x) fig 1 .0835 ref 2.121 "a" "a" ba ba c l c-117-01-x c-117-01-x c1 x .0050[.127] ref 0.279 (see note 3 and 7) .008 (no of pos. x .03937[1.0000] + .0125[.318]) (see note 8) 1.000 .0394 .0110 .1000 2.540 ref c sheet of e - m a i l i n f o @ s a m t e c . c o m c o d e 5 5 3 2 2 dimensions are in inches. tolerances are: decimals angles this document contains information unless otherwise specified, 9. coplanarity to be .0040 for positions 2-25 .xx: & .0060 for positions 26-50. samtec, inc. and shall not be reproduced confidential and proprietary to .0020 [.051] material: low profile 1mm x 1mm double row body by: clm-1xx-xx-xx-d-xx dwg. no. description: proprietary note .xxxx: .005 [.13] .xxx: .01 [.3] 2 consent of samtec, inc. d o n o t s c a l e d r a w i n g g. purvis 08/10/94 2 1 s h e e t s c a l e : 2 : 1 obtained without the expressed written color: black f:\dwg\misc\mktg\clm-1xx-xx-xx-d-xx-mkt.slddrw body: lcp, ul 94 vo phos bronze terminal: purpose other than that which it was disclosed to others or used for any or transferred to other documents or notes: 1. represents critical dimension. 2 . minimum pushout force: .5 lb. 3. will lose a position for every cut made on a socket strip. 4. positions -05 through -50 are to be tubed. positions -02 thru -04 to be layer packaged only. 5. shear tails to dimensions shown, .003 max shear burr. 6. parts to be symmetrical about c l . 7. cut flash to be .010 [.25] max with no flash allowed in holes or extending below leads. 8. endwall after cutting: .0155.0025 [.398.064] 5 2 0 p a r k e a s t b l v d , n e w a l b a n y , i n 4 7 1 5 0 p h o n e : 8 1 2 - 9 4 4 - 6 7 3 3 f a x : 8 1 2 - 9 4 8 - 5 0 4 7 revision ba fig 2 (same as fig 1 except insulator) c3 c2 burr side (see note 5) section "a"-"a" scale 4 : 1 see note 9 2.248 (measured at bend) .0885 3 90 .150 .010 3.81 0.254 (see note 5) ref no. of pos x .03937[1.0000] - .03937[1.0000]
c l .1185 3.010 .0535 1.359 ref .275 6.99 .035 0.89 (typ) fig 5 -a: molded alignment pin .020 ref 0.51 (no of pos. -2) x .03937 [1.0000] .020 0.51 .015 ref 0.38 .0966 2.454 .144 3.66 ref c l fig 3 -p: pick & place pad available on positions 7 thru 50 only note: "n" = used measured dimension (ref) " q " = { ( " n " - . 2 2 5 [ 5 . 7 2 ] ) / 2 } .020[.51] lmp-04 ba "n" .225 5.72 ref "q" c l c l fig 4 -pa: pick & place pad with alignment pins ppp-39-x-x-xx "m" "a" "p" .325 8.26 ref sheet of low profile 1mm x 1mm double row body by: clm-1xx-xx-xx-d-xx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. d o n o t s c a l e d r a w i n g g. purvis 08/10/94 2 2 s h e e t s c a l e : 4 : 1 revision ba f:\dwg\misc\mktg\clm-1xx-xx-xx-d-xx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 note: "r" = used measured dimension (ref) " s " = { ( " r " - . 1 3 8 [ 3 . 5 0 ] ) / 2 } .020[.51] "s" "r" .019 .010 0.48 0.25 .138 3.51 .0935 ref 2.375 pt-clx001-d pt-clp001-pa pt-1-24-01-50 fig 6 -k: polyamide film pad available on positions 7 thru 50 only -packaging (see note 4) table 1 pos / row "a" "m" "p" 4-15 .140[3.58] ref used measured dimension(ref) {("m" - "a") / 2} .010[.25] 16-50 .280[7.11] ref table 3 positions pad even 4-14 ppp-39-e-4-15 16-50 ppp-39-e-16-50 odd 5-15 ppp-39-o-4-15 17-49 ppp-39-0-16-50 table 2 (includes -d & -d-be) option tube plug -p, -a-p pt-clx001-d tp-33 -pa pt-clp001-pa tp-09 -none -a, -a-k, -k pt-1-24-01-50 tp-33
|
